The job description of a locksmith regulates labor relations. The document contains general provisions on the position, requirements for education, work experience, knowledge, the order of subordination, employment and dismissal of the employee from the post, a list of his functional duties, rights, types of responsibility.

The instruction is developed by the head of the organization. The document is approved by the director of the organization.

The standard form provided below can be used in the preparation of the job description of a mechanic for assembly, a toolmaker, for car repair, etc. A number of provisions of the document may vary depending on the specialization of the employee.

Sample model fitter job description

І. General Provisions

1. Locksmith belongs to the category of "workers".

2. Locksmith directly reports to the head of the unit / general director of the organization.

3. The appointment and dismissal of a locksmith is made by order of the Director General.

4. A person with an education in a profile not lower than secondary specialized and experience in similar work for at least one year is appointed to the position of a locksmith.

5. During the absence of the locksmith, his rights, functional duties, and responsibilities are transferred to another official, as reported in the order for the organization.

6. Locksmith in its activities is guided by:

• internal labor regulations;
• this job description;
• Company charter;
• guiding, regulatory acts of the organization;
• orders, instructions of the management;
• orders of the immediate superior;
• the legislation of the Russian Federation.

7. Locksmith must know:

• principles of operation, equipment, methods of restoring worn-out structures;
• the procedure for disassembling, repairing, assembling parts, installing units, assemblies, handling devices;
• requirements for fit, tolerances, accuracy classes of parts;
• time standards for the performance of work;
• methods and conditions for the use of special, auxiliary equipment, measuring equipment;
• norms for consuming materials, spare parts;
• conditions for testing, commissioning, receiving mechanisms, components, assemblies after maintenance and repair;
• rules of circulation, the appointment of mechanized tools.

II. Job duties of a locksmith

Locksmith performs the following duties:

1. Sorts parts according to the criterion of performance after disassembly, cleaning.

2. Processes nodes, parts, carries out their static balancing.

3. Carries out verification, inspection, routine inspection of parts and mechanisms.

4. Eliminates established malfunctions, defects during the diagnosis period by decision of the immediate supervisor.

5. Assembles, adjusts, replaces spare parts, components, assemblies, equipment in accordance with the received order.

6. Informs the immediate supervisor of the identified malfunctions of parts, mechanisms and necessary measures for their elimination.

7. Disassembles, assembles, repairs components, equipment parts in accordance with the guidelines of the organization for the work.

8. Uses protective clothing, installed personal protective equipment during work.

9. Applies devices, devices in compliance with safety regulations and fire protection.

10. Determines the causes of increased wear, failure of parts and mechanisms.

11. Prepares documents for the provision of materials, spare parts, tools.

12. Supports good work, timely inspection of parts and mechanisms.

13. Carefully spends and rationally applies the entrusted tools, devices.

ІІІ. Rights

Locksmith has the right:

1. Do not begin to perform their functional duties in the event of a danger to life and health.

2. Communicate with the organization's departments on work issues.

3. Participate in educational activities, improve their skills.

4. Demand from the management of the organization the formation of normal conditions for safe work, the exercise of their powers.

5. Inform the management of the identified deficiencies in the activities of the organization, send suggestions to address them.

6. Consult with specialists on issues beyond the competence of a locksmith.

7. Receive information from managers about decisions regarding its activities.

8. To inform the management of proposals for improving the activities of the organization.

9. Make decisions independently within their competence.

ІV. A responsibility

Locksmith is responsible for:

1. Improper performance of their duties.

3. Violation of the provisions of the organization's governing documents.

4. The reliability of the information provided to the management on the functioning of mechanisms and equipment.

5. The results of independent decisions, own actions.

6. Violation of safety standards, labor discipline, fire protection standards, internal labor requirements.

7. Causing damage to the organization, its employees, the state, customers.

Repairman

Repairman repairs, restores parts, mechanisms of equipment that is used for industrial, domestic, technical activities.

Specific functional responsibilities of a repairman:

1. Scheduled preventive maintenance of equipment, in accordance with the established schedule.

2. Accounting for the current mandrel, devices.

3. Machine settings.

4. Processing of units, parts according to established qualifications (degrees of accuracy).

A mechanic for assembly works (SMR) works in the shops of organizations involved in mechanical engineering and metalworking. This profession can be practiced by both men and women, but they mainly work on it. males.

Related professions, which are also owned by SMR, are a fitter for instrumentation and automatic devices, as well as a tool maker. The activity takes place in special workshops of institutions involved in mechanical engineering and working with metal, where it is possible to carry out locksmith and assembly work from the special parts provided for various devices, including complex ones: cars, tractors, motors, turbines and various machine tools.

First, the construction and installation work, using the necessary devices, adjusts, connects and fastens the intended product among themselves, and then tests it on special installations and, if necessary, adjusts it for further uninterrupted operation.

Ranks and characteristics of activity

Construction and installation work various difficulty levels. The right to this activity determines its tariff category. They are registered in the tariff-qualification reference book, the same for each enterprise. Today, there are categories 2 to 7:

General Provisions

This section of the document should contain official job title   according to the template prescribed in the manuals of workers' qualifications, accepted standards and the current staffing adopted at a particular organization. Also indicated here all requirements   to his necessary education, qualifications and accumulated working experience.

Requirements and Responsibilities

The most important point of this documentwhich should be spelled out in more detail. The list of duties depends on the type of enterprise on which SMR works and his immediate profession. The general lesson for all construction and installation works consists only in the assembly of parts of mechanisms and integral structures.

Other responsibilities depend on many factors. The main thing is a special point of the rules where the technological process and safety measures are prescribed, which must be observed during operation. Particular attention should be paid to it for construction and installation works of a high category, which must gradually follow its traumatic technological process.

• installation of whole products or only their individual parts;
• tuning and processing of units and parts;
• testing of finished products on special machines;
• elimination of errors that occurred during assembly;
• balancing the main nodes of the assembled units;
• securing all joints with a hydraulic press.
    Rights and Responsibilities

This part of the contract mainly involves general rights of the country's labor lawtherefore, only specific species accepted at the enterprise are often indicated here. The sections of responsibility are devoted to the rights of the employee, which are fixed by law.

Employers do not often introduce additional rights for their employees in the enterprise, but job descriptions often include following list:

• the right to refuse activities that pose a danger to the life and health of SMR and other people;
• the right to directly contact (including with written statements) to his immediate supervisor on all issues arising during the work process;
• the right to inform his immediate supervisor about the failure of the mechanisms and, if possible, independently carry out measures to eliminate them.

Responsibility for violation of an employment contract is also the same in almost every organization, therefore it does not make sense to describe it in detail if there are no special paragraphs of the rules. Mentioned mainly of disciplinary, criminal and material liability in cases provided by law.

Qualifications and experience

SMR must have professional education. Requirements for him will be presented depending on the complexity of the necessary work that he is obliged to perform, that is, on his discharge. This section provides guidance on the work experience of construction and installation work.

There is only one rule: the higher the category is necessary for work in a specialty, the longer should be the length of service in it.

This paragraph of the instructions contains list of works, which must accurately perform construction and installation work at the enterprise. They directly depend on the category of the employee and are prescribed in the qualification characteristics of the ETKS SMR directory.

Accordingly, the higher the category, the more complex production tasks he must be able to fulfill and comply with all the production requirements specified in the instructions at a particular enterprise. The ETKS SMR directory is approved by the legislation of the country and is the same in all enterprises, large and small.

Assessment, working conditions, professional standard

The direct supervisor of the construction and installation work at this point of instruction:

1. It assesses the labor activity of its employee, comparing the measured indicators with the functional ones.
2. Prescribes the labor functions included in the professional standard for construction and installation work of the specified working rank, making up a functional map of the type of his professional activity. The development organizations of the selected professional standard for this paragraph of the instruction should be indicated here.
3. Indicates the conditions of activity at the enterprise: describes the workplace, the mode of work and rest, occupational hazards, the need and frequency of business trips. Also here additional conditions of activity are prescribed that do not violate the rights of the employee in a single enterprise, corresponding to the concluded contract and other agreements, as well as other regulatory acts, non-disclosure of official and commercial secrets of the organization.

Post Relations

The СМР instructions stipulate direct interaction with other divisions of the enterprise and employees on it, from which it receives direct instructions or, on the contrary, transfers materials to fulfill the assigned tasks. Their composition and terms of transfer are registered.

The employee’s place in the organization, his superiors and subordinates, as well as shift workers during his absence from work for a good reason are indicated. High-level construction and installation works are often the heads of less experienced workers, and they themselves are subordinates of the head of the corresponding workshop where he works.

Must be negotiated   interactions of workers of different categories with units involved in the elimination of accidents, the prevention of dangerous situations and the elimination of the consequences of emergency.

In small organizations, the direct head of construction and installation work may be directly its head, as well as the deputy head of production. All this is negotiated in special subparagraphs of the job description SMR.

At the end of the job description of the mechanic assembly machine, the document on the basis of which it was developed should be indicated, as well as its name and the release date of both this document and the job description.

How to become a mechanic for mechanical assembly work? The answer to the question is in the video.

The activities of a locksmith are associated with the repair of equipment necessary to maintain basic human needs. These specialists are at all large enterprises.

This specialty is divided into narrow specializations:

• plumbers;
• toolmakers;
• car mechanics;
• mining equipment repairmen;
• chemical repair technicians;
• emergency repair fitter;
• machine repair technicians;
• general fitters, etc.

Locksmiths assemble mechanisms and ensure their quality work.

The word “locksmith” is an interpretation of the German word lock, and “repairman” is translated from French as a replacement. Previously, these workers were engaged in the replacement of locks. The most famous repairman in Russia was Lefty from the story of Leskov, who was able to skillfully shoe a flea.

What does a repairman do

The main functions are:

• assembly of mechanisms;
• markup;
• replacement of mechanisms;
• cutting
• metal filing;
• thread cutting;
• scraping;
• grinding in.
• drilling, etc.

Any mechanisms and machines periodically fail, so a locksmith is needed in any production process. He carries out maintenance and overhaul of machine tools and machines, as well as carries out their installation and adjustment. Diagnostics of the technical condition of devices and apparatuses before starting work is carried out, the degree of wear of the equipment is determined.

When carrying out any repair work, a detailed plan is drawn up and, if necessary, drawings of parts requiring replacement are made. In the course of its activities, the repairman fills out the relevant documentation confirming interference with the operation of devices and mechanisms. This documentation is a legal document, its preparation requires care and meticulousness.

Also, a repairman makes devices that facilitate labor and increase its productivity. After repair, the equipment is tested, and only after that it is recognized as a worker. In case of failure of the production equipment, the locksmith must ensure its repair as soon as possible. The efficiency of the entire enterprise depends on the timely arrival of this specialist.

Traits suitable for the repairman profession

This profession does not require excessive expenditure of physical strength. To work with pleasure, you need to love your work, so people who are interested in technology and machines will find themselves in this specialty. Likewise, a fitter should have an accurate eye, resourcefulness, tenacity, perseverance, accuracy, punctuality, well-developed fine motor skills of hands, imaginative memory and spatial imagination, and many other qualities useful for work.

Since this specialization covers a fairly wide area of \u200b\u200bactivity, the representative of this profession should have in-depth knowledge relating to all areas of his professional activity. Before doing repairs, you need to know the structure and principle of operation of technology, and this is possible only by studying the fundamental laws of physics.

Safety during the repair should be strictly observed to eliminate the threat to the life and health of the employee. To understand the operation of a device, you need to be well-versed in the schemes of its operation. During routine inspections of equipment, it is required to warn of possible breakdowns in certain places, which is done by a repairman.

Why choose the profession of a repairman?

Every year more and more complex mechanisms and machines appear in the world. Their service requires professionally trained workers, so the number of jobs will only increase. Competent specialists will be provided not only with a prestigious job, but also with a decent salary. In carrying out his work, you have to use a wide variety of tools, so the locksmith has the skills to work with any toolkit.

What are the disadvantages of the profession of a repairman?

To become a locksmith, you need to get a secondary vocational education. To do this, just graduate from college or college. The shortage of these specialists has led to the fact that a large number of colleges began to teach students in this direction. To work, you need to have deep theoretical knowledge and, most importantly, practical skills. Only in the course of work can all the material studied be consolidated. The more a locksmith is engaged in his professional activities, the more experienced he becomes. During the training, it is mandatory to undergo practical training, where all acquired skills are honed.

Working conditions of a locksmith

You will have to work indoors, but sometimes you need to do work outdoors. must be equipped with tools and measuring instruments. Also, depending on the field of activity, the presence of machine tools, workbenches and other devices is possible.

The following tools should be available: scissors, file, chisel, locksmith hammers, wrenches, pliers, screwdrivers, hacksaws and much more. Work clothes should be provided to the specialist. In summer, overalls and special protective gloves are used, in winter these are warm trousers and a jacket.
  Health risks.

There are a number of adverse factors that poorly affect the health and general well-being of a locksmith. These include a long stay in an uncomfortable position, since many manipulations have to be performed in a limited space. In this regard, often there are diseases of the musculoskeletal system, manifested by pain in the back and joints, deformation of the fingers. The cardiovascular system suffers and the likelihood of developing hypertension is high.

When working with equipment, a very intense noise and vibration occurs, which is fraught with hearing impairment. To prevent the development of hearing problems, special headphones are used that reduce the sound intensity. Long hard work can cause the development of myopia. To protect your eyes from dust, use transparent glasses. When working, harmful substances are released, which in the future can lead to occupational lung diseases. Using a mask solves this problem.

Bearing buyers attention

Unified Tariff and Qualification Handbook of Jobs and Professions of Workers (ETKS), 2019
Part No. 2 of issue No. 2 ETKS
  The issue is approved by the Resolution of the Ministry of Labor of the Russian Federation of November 15, 1999 N 45
  (as amended by Order of the Ministry of Health and Social Development of the Russian Federation of November 13, 2008 N 645)

Mechanical Assembly Worker

§ 87. Locksmith of mechanical assembly works of the 2nd category

Description of work. Assembly and adjustment of simple units and mechanisms. Locksmith processing and fitting of parts according to 12-14 qualifications. Assembly of nodes and mechanisms of medium complexity using special devices. Assembly of parts for tack and welding. Cutting of blanks from a bar and a sheet on hand scissors and hacksaws. Chamfering. Drilling holes according to the marking, the jig on a simple drilling machine, as well as pneumatic and electric machines. Thread cutting with taps and dies. Marking up simple parts. Connection of parts and assemblies by soldering, glues, bolts and cold riveting. Testing of assembled units and mechanisms on benches and presses of hydraulic pressure. Participation together with a fitter of higher qualification in the assembly of complex units and machines with fitting parts, in the adjustment of gears with the installation of the lateral and radial clearances specified in the drawing and specifications.

Must know:   technical conditions for assembled units and mechanisms, the name and purpose of a simple working tool; name and marking of processed materials; a system of tolerances and landings of assembled units and mechanisms; basic mechanical properties of the processed metals; ways to eliminate deformation during heat treatment and welding; causes of corrosion and ways to combat it; purpose and rules for the use of instrumentation and the most common special and universal devices; purpose of lubricating fluids and methods of their use; rules for marking up simple parts.

Work examples

1. Car - assembly of the steering wheel, hood, bracket and gearbox assemblies.

2. Hydraulic shock absorbers - installation.

3. Headstock rear lathes - assembly.

4. Blocks on rolling and sliding bearings - assembly.

5. Friction rollers - installation.

6. Shut-off valves for air, oil and water - installation in place.

7. Spindle of textile machines - running-in.

8. Swivel forks - filing through the liner and bracket.

9. Air ducts of the main highways of passenger and freight cars of all types - assembly.

11. Parts and connections - hydraulic pressure test.

12. Flat parts - scrapping of rectangular open planes for interfacing fixed parts (brackets, racks, etc.) with an accuracy of two points on a surface of 1 square. cm.

13. The details are different - filing and fitting in place, drilling and drilling holes that do not require high accuracy.

14. Door locks, internal - fitting of parts and assembly.

15. Fasteners, loops, chains with free sizes (simple) - manufacturing.

16. Carriages of lathes - assembly.

17. Frames for turbines - assembly.

18. Bearing housings - boring assembly.

19. Covers for instrument housings (bronze, aluminum, cast iron) - marking, filing, drilling holes with a diameter of up to 25 mm.

20. Casing covers - fitting and installation on the machine.

21. Lifting winches with a manual drive with a loading capacity up to 10 t - assembly and testing.

22. Sliding clutches, cylindrical and worm gears - filing and fitting of keyways.

23. Knives of cutting units - editing.

24. Bends, tees for pipelines - hydraulic testing and assembly.

25. Hinges, hinges - marking, manufacturing, assembly and installation in place.

26. Stands for children's percussion musical instruments - assembly.

27. Thrust ball bearings single row, angular contact single row and angular needle with cylindrical and twisted rollers with an outer diameter of up to 500 mm - assembly.

28. Coil springs for engine valves - stress test.

29. Springs, brushes with a base, levers, brush holders for traverses of electric machines - assembly, riveting, soldering.

30. Tanks - compressed air test to the maximum pressure.

31. Driver's seat - installation.

32. The upper and lower all-metal wagons are used - assembly with fit.

33. Transmission of the crane movement mechanism - assembly.

34. Oil, water and air filters - assembly.

35. Kettles, coffee pots, milk jugs - filing spouts.

36. Cast gears and racks of various module - filing teeth according to templates.

37. Detachable pulleys - assembly.

38. Prismatic, wedge, tangent dowels up to 24 x 14 x 300 mm in size - filing.

39. Metallic shelves - assembly.

40. Battery and tool boxes - assembly, gluing.

§ 88. Locksmith of mechanical assembly works of the 3rd category

Description of work. Locksmith processing and fitting of parts in the range of 11-12 qualifications using universal devices. Assembly, adjustment and testing of units and mechanisms of medium complexity and plumbing according to 7-10 qualifications. Marking, scrapping, grinding of parts and assemblies of medium complexity. Elementary calculations to determine tolerances, fit and taper. Pressing parts on hydraulic and screw mechanical presses. Testing of assembled units and mechanisms at special facilities. Elimination of defects found during assembly and testing of units and mechanisms. Adjustment of gears with installation of lateral and radial clearances given by the drawing and technical conditions. Static and dynamic balancing of various parts of a simple configuration on special balancing machines with a spark disk, prisms and rollers. Soldering with various solders. Assembly of complex machines, assemblies and machine tools under the guidance of a higher qualification fitter. Management of handling equipment from the floor. Slinging and linking goods for lifting, moving; installation and storage.

Must know:   device and principle of operation of assembled units, mechanisms and machines, technical conditions for their assembly; mechanical properties of processed metals and the effect of heat treatment on them; types of rivets and welded joints and conditions for ensuring their strength; composition of refractory and fusible solders, fluxes, mordants and methods for their preparation; device of medium complexity of instrumentation and devices; rules for sharpening and fine-tuning the bench tool; tolerance and landing system; Qualities and roughness parameters ways to mark parts of medium complexity.

Work examples

1. Cars - assembly of the cab, body, rear axle.

2. Auto barriers - filing of a sector along a shaft.

3. Refrigeration units - installation on the outer wall.

4. Shock absorbers type AKM-400 and the like - complete final assembly.

5. Ship fittings of all types and sizes with manual transmission, gears - assembly, adjustment, testing, delivery.

6. Drums of a mechanical razor - assembly, check of face and radial runout of a tooth.

7. Cylinder blocks of internal combustion engines - threading in holes within a given accuracy class and crimping with hydraulic pressure before final assembly.

8. Shafts - crimping bushings, flywheels, couplings.

9. Crankshafts of internal combustion engines - manual cutting of threads in blind holes.

10. Valves of all diameters - valve grinding and hydraulic testing.

11. Fans, motors - assembly, adjustment.

12. Inserts, glasses, chairs, rags and other details - threading with a diameter of up to 2 mm and over 24 to 42 mm for the passage and at point-blank range.

13. Air separators - general assembly.

14. Hand views of all types and sizes - assembly.

15. Heads and rings of the cardan - assembly, drilling in a jig with subsequent pinning.

16. Sliding doors - manufacturing.

17. Details of locks - manufacturing.

18. Internal combustion engines with power up to 73.6 kW (100 hp) - general assembly.

19. Disks of rotors, compressors, turbines - marking, plumbing.

20. Clutch discs, brake linings - assembly, gluing.

21. Combination car locks with a halyard, vestibule doors for passenger cars - fitting of parts and assembly.

22. Throttle butterfly valves with manual transmission of all types and sizes - assembly and testing.

23. The teeth of the gears of the box of the car and trolley - filing.

24. Heating chambers of diffusion furnaces, cooling systems for vacuum installations - assembly.

25. Carter hitch - fitting tubes with fit.

26. Valves of high pressure and shunting device - grinding in saddles.

27. Valves and taps, air and water - lapping.

28. Water gauge columns with Clinker devices - assembly, testing, delivery.

29. Protective housings of complex structures - assembly.

30. Casing for sheathing - manufacturing.

31. Piston rings - sawing out the lock and scrapping.

32. Retaining rings - marking, drilling, fitting.

33. Compensators - assembly and testing.

34. Oil controllers - assembly and adjustment.

35. Gearboxes - assembly and testing.

36. Distribution boxes - full production (without installation).

37. Cases of block boxes - manufacturing.

38. Cases and frames welded from various materials with dimensions of 500 x 500 x 700 mm - assembly with a tack, editing.

39. Cases, brackets - scraping.

40. Compressor housings - assembly.

41. Cases of covers - fitting with the scraping of grooves and wedges to them.

42. Instrument cases - installation of parts in the case, fitting of covers with a casing on locks, hinges, stops.

43. Gas taps - grinding in of conical surfaces.

44. Lifting winches with a mechanical drive - assembly and testing.

45. Elevators - assembly.

46. \u200b\u200bTraction mechanisms, manipulators, access hatches, stopper, anchor rope drives, small rudder drives - assembly, testing, delivery.

47. Bridges (from a bar) for fastening a wire - manufacturing, installation.

48. Piston pumps - assembly and testing.

49. Shells - assembly with flanges.

50. Flexible supports - assembly, straightening.

51. Axes, tail rotors, springs and leashes in mechanical numbering devices - replacement.

52. Base, panels, plates - filing, marking, drilling holes in different planes, threading.

53. Holes for ball bearings - fine-tuning.

54. Packages of cast blades - assembly and fit for welding.

55. Panels of complex design - manufacturing.

56. Adapters rubber - manufacturing.

57. Testing plates - scraping.

58. Stands for single plates - assembly, adjustment.

59. Plain bearings with a diameter of up to 300 mm - scrapping.

60. Ship bearings and thrust bearings - laying of liners in the bed of hulls and covers without additional adjustment with checking the mating surfaces with a probe with an accuracy of 0.05 mm.

61. Ball and radial bearings, single row, ball radial spherical, double row with an outer diameter of more than 500 mm - completing and assembling.

62. Pistons - assembly with connecting rod and fitting of the piston ring.

63. Drives for gearboxes, mills and screws - assembly.

64. Devices for removing half-couplings, bearing rings - assembly.

65. Corrugated gaskets - production according to the drawing.

66. Copper gaskets with asbestos filler - manufacture.

67. Frames and wings of snow plow plows - assembly for welding.

68. Anchor gear reducers - assembly.

69. Turbine rotors and stators - set and installation of blades.

70. Sealed metal hoses for fittings - assembly.

71. Steel shaped handles - marking and filing a contour according to a marking or template.

72. Steel levers - metalwork, assembly with bushings.

73. Bulkhead, cone, ventilation glasses, sensors with cone inserts, etc. - adjustment of parts during manufacture, final assembly, adjustment and testing.

74. Beds of metal-cutting machine tools - scraping.

75. Racks of block mechanisms - filing.

76. Stands rails and awnings, buttresses - fitting, assembly.

77. Metal chests for spare parts - manufacturing of parts and assembly.

78. Calipers of lathes - assembly.

79. Bedside tables tool machinist - assembly.

80. Control cabinets - assembly, delivery.

81. Cellular seals - manufacturing.

82. Rectangular flanges for ducts and fittings of industrial ventilation systems - manufacturing.

83. Foundations for auxiliary mechanisms of small vessels - installation.

84. Chlorinators - assembly and testing.

85. Tanks and tanks - assembly for welding.

86. Hinges for piano covers and grand pianos - assembly.

87. High precision ball bearings - assembly and installation.

88. Connecting rods - scrapping, fitting bushings and assemblies.

89. Bevel gears - manual sawing of teeth.

90. Combined gears - assembly with check indicator.

91. Gears and racks of various modules - assembly of teeth in pair with ensuring the required clearance and contact.

92. Tires - production according to the drawings.

93. Hoses with couplings without crimping under a press - assembly.

94. Hoses with wire harness, clamping for hydraulic testing from 15 - 30 kgf / sq. cm.

95. Augers and conveyors of medium complexity - assembly.

96. Switchboards one-and two-panel open and closed execution - complete manufacturing and assembly without installation.

97. Ejectors with a capacity of up to 100 t / h - assembly of stamped halves for welding in fixtures, sweep with other parts and testing.

§ 89. Locksmith of mechanical assembly works of the 4th category

Description of work. Plumbing and fitting of large parts and complex units according to 7-10 qualifications. Assembly, adjustment and testing of complex assemblies of units, machines and machine tools. Lapping and scraping of mating surfaces of complex parts and assemblies. Cutting internal grooves, splined joints - involute and simple. Adjustment of interference and clearances, centering of mounted parts, assemblies and assemblies. Installation of pipelines operating under air pressure and aggressive special products. Static and dynamic balancing of machine units and parts of complex configuration on special balancing machines. Elimination of defects found during assembly and testing of units, assemblies, machines. Pressing parts on hydraulic and screw mechanical presses. Participation in the installation and dismantling of test benches, in the assembly, adjustment and testing of complex experimental and unique machines under the guidance of a more qualified technician.

Must know: design, kinematic diagram and principle of operation of assembled units of mechanisms, machines; technical specifications for the installation, adjustment and acceptance of assembled units, machines; device, purpose and rules for the use of working, instrumentation, instruments and appliances; tolerance and landing system; Qualities and roughness parameters principles of interchangeability of parts and assemblies; methods for marking complex parts and assemblies; a method of heat treatment and refinement of a complex bench tool; ways to prevent and eliminate the deformation of metals and internal stresses during heat treatment and welding; fundamentals of mechanics and metal technology within the scope of the work performed.

2. Ship fittings - manual grinding and lapping of sealing surfaces.

3. Mixing drums with internal spirals - assembly.

4. Blocks of internal combustion cylinders - scrapping of areas under the crankshaft bearing caps.

5. Propeller shafts with a diameter of up to 250 mm - scraping cones and fitting keyways in caliber.

6. Shafts of gears of auxiliary mechanisms - laying of shafts with fitting of bearings.

7. Support crowns - assembly.

8. Propellers for shafts - fitting the hub on the shaft cone and caliber.

9. Liners of a thrust bearing - assembly with a segment.

10. Inserts for ship bearings - flange of connectors flush with the connectors of the housings and covers with an accuracy of 0.02 mm and ensuring the interchangeability of parts.

11. Deadwood bushings with rubber-metal liners for shafts with linings - assembly of liners in caliber.

12. Bushings, presses, levers in automatic numbering devices - replacement.

13. Drilling towers - assembly of individual structures.

14. Hydraulic supports, hydraulic valves - assembly and final refinement.

15. Reel lift cylinders - assembly and testing.

16. Mushroom-shaped ventilation heads with manual transmission of all sizes - assembly and testing.

17. Combs, crutches and inner cones in mechanical numbering devices - replacement.

18. Alarm sensors, sensor drives - adjustment with installation on gate valves.

19. Internal combustion engines with a power exceeding 73.6 to 736 kW (100 to 1000 hp) - general assembly.

20. Details are complex - deployment of holes in inaccessible places.

21. Details with grooves and slots of the dovetail shape - metalwork.

22. Diesels - assembly and installation of the connecting rod and piston group.

23. Friction disks with a diameter of up to 300 mm - grinding in with a tolerance on the plane and straightness within 0.01 mm.

24. Piano locks - assembly.

25. Captures rail-cutting switch junctions, cores of block mechanisms, captures of a six-ton \u200b\u200bsteam valve, covers of turbogenerators - assembly.

26. Flaps with conical and worm gearing with a diameter of 150 to 250 mm - assembly.

27. Ship casting, receiving and ventilation flaps with nominal bore of 350 mm and above - fitting of rubber seal, assembly, adjustment.

28. Diamond core drills - cleaning of base surfaces, opening of diamonds.

29. Caliber propeller shafts and propellers - scraper and fit the cone with dowels.

30. Frames for radio devices from profile steel with the number of incoming parts up to 50 - assembly.

31. Kingstones with nominal bore over 275 mm, with nominal pressure up to 50 kgf / sq. cm - grinding plates and nests, assembly, testing, delivery.

32. Automatic valves (steam and water) - assembly, adjustment, testing, delivery.

33. Quick-locking and steam valves, turbine boxes - bulkhead after bench tests.

34. High pressure valves, o-rings - lapping.

35. Safety, pressure-reducing, drainage, overflow, non-return and non-return-shut-off valves, boiler and safety, main and control pressure levels 1 and 2 (up to 30 kgf / sq. Cm) - assembly, adjustment, testing, delivery.

36. Direct-flow remote control valves with actuator - assembly, adjustment, delivery.

37. Clinkets with nominal bore up to 875 mm - scraping and grinding of wedge surfaces, assembly, testing, delivery.

38. Columns of water-measuring ship steam boilers of complex systems with a working pressure of more than 25 kgf / sq. cm - assembly, adjustment, testing, delivery.

39. Compressors and drying units (BO) with a gas supply under pressure up to 230 kgf / sq. cm - installation on a stand, installation, testing according to a given program, dismantling, elimination of minor defects in the system.

40. Boxes of reverse motor vehicles and cargo railcar - windows scraping.

41. Boxes of the central drive - assembly.

42. Shells and frames welded of various materials - assembly.

43. Cases and brackets - scraping the plane according to 2 qualifications.

44. Cases and covers of complex configuration of large dimensions - metalwork with fitting and installation of joints of locks and hinges.

45. Cases of nozzle apparatuses - assembly.

46. \u200b\u200bBrackets for running servomotors - assembly.

47. Gas-tight covers with a drive - assembly and testing.

48. Sealing covers - assembly of rings.

49. Grinding wheels with a diameter of up to 750 mm - assembly, testing, balancing.

50. Labyrinths - installation and mounting.

51. Manipulators - scraping, grinding.

52. Paper-making and paper-making machines - assembly.

53. Hydraulic drive machines for flaps and other mechanisms - final assembly, adjustment, testing, delivery.

54. The main, auxiliary and aggregate mechanisms - installation, alignment, assembly using plastics.

55. Locking mechanisms - assembly and adjustment.

56. Mechanisms and fittings of remotely controlled ship and ship systems - test.

57. Mechanisms - assembly and mechanical adjustment according to 2 qualifications.

58. Planetary mechanisms - assembly.

59. Hydraulic control bridge - assembly, adjustment.

60. Cam couplings - fit.

61. Trigger clutches - final processing after hardening.

63. Ship oil heaters - assembly.

64. Holders - assembly with a shock segment.

65. Holders and shields - assembly with seal plates.

66. Engine mounts - assembly.

67. Tape drive axis - locksmithing and assembly.

68. Coolers, distillers, condensers - assembly.

69. Compound fittings - assembly, scraping and fitting.

70. Turnouts double cross - assembly.

71. Angular gear transmissions - assembly, adjustment with the provision of the required clearance and touch spot.

72. Angular control of clinkets and valves - assembly, adjustment, delivery.

73. Turnouts double cross - assembly.

74. Feather of a rudder with a baller - scraping of cones and keyways, fitting, assembly, delivery.

75. A rudder feather and a balloon with a flange connection - scrapping of the flange planes, assembly of the connection, alignment of the center line, opening holes.

76. Pneumatic cylinders - assembly and adjustment.

77. Stands for paired plates - assembly.

78. Friction bearings, consisting of several parts - scrapping.

79. Bearings with tapered bores - assembly.

80. Bearings ship support, thrust and auxiliary for shafts with a diameter of up to 300 mm - scraping of beds and liners.

81. Bearings (ball and roller) of all sizes, produced in accuracy classes A, B and C, - completing and assembling.

82. Crawlers of turnout electric drives - cutting corners, planes, chamfers and exits from the annular groove.

83. Hydraulic presses with a capacity of up to 3000 t - assembly and installation.

84. Drives to ball mills - assembly and adjustment.

85. Springs - calibration and load testing with verification according to the table.

86. Gearboxes - assembly, adjustment, testing.

87. Worm gears - worm gear scraping.

88. Springs - assembly.

89. Rotors and stators of steam and gas turbines - assembly.

90. Levers in the block mechanisms - fit in the sector.

91. Loaders, rotary and flat-printing machines, semi-automatic machines for casting stereotypes - assembly.

92. Contact selsins - installation and adjustment of traverses, dampers, installation of ball bearings, running-in, adjustment of axial play, fine-tuning, pre-assembly, static balancing.

93. Separators - manual insertion of rivets using a mechanism, insertion of roller rings, charging with rollers.

94. Special pipe systems - scraping, polishing the inner pipes.

95. Beds of large metalworking machines - scraping guides.

96. Machine tools - wrapping, labeling, evaporation and vacuum machines, linear cutting and stamping units - assembly.

97. Carts of motor platforms of track layers - marking and installation of jaws.

98. Band brakes with gearbox - worm gear attachment with provision of a touch spot, assembly.

99. Steam and gas turbines - fitting and installation of blades and assembly of thrust bearings.

100. Filter plants - assembly.

101. Dehumidification devices of vacuum spraying installations - assembly of units.

102. Flushing devices for water desalination plants - assembly.

103. Filters of complex structures dual - assembly, delivery.

104. Trunks of filling machines - assembly.

105. Refrigerators - assembly of units, door installation and testing.

106. Precision ball bearings (performance according to special specifications) - assembly and installation.

107. Hoses with compression on the press for hydraulic tests with pressure up to 300 kgf / sq. cm - assembly.

108. Eccentrics, cams and counterweights of the turbogenerator regulator - file sawing according to templates.

109. Ejectors with a capacity of over 100 t / h - assembly of stamped halves for welding in fixtures, fitting with other parts and testing.

110. Electric blowers and turbo blowers - assembly.

§ 90. Locksmith of mechanical assembly works of the 5th category

Description of work. Plumbing and finishing of thermally untreated parts, products and units of a complex configuration of 6 qualifications and a complex configuration of 7 qualifications. Assembly, adjustment and debugging of complex machines, instrumentation, remotes and instruments, unique and precision units and machines, selection and assembly of large and combined bearings. Testing pressure vessels, as well as a deep vacuum test. The removal of the necessary diagrams and characteristics according to the test results and the delivery of OTC machines. Installation and dismantling of test benches. Testing complex unique and precision metal-cutting equipment for accuracy and compliance with technical specifications. Installation of pipelines operating under high pressure of air (gas), and special products. Static and dynamic balancing of parts and assemblies of complex configuration.

Must know:   design, purpose and principle of operation of assembled complex mechanisms, devices, assemblies, machine tools and machines; technical conditions for adjustment, testing and delivery of assembled units of machines and assemblies and their operational data; methods of assembly and adjustment of machines and test modes; measures to prevent deformation of parts; rules for checking machines for accuracy.

Work examples

1. Guards and distribution apparatus of mechanical centralization - assembly and adjustment.

2. Locking and adjusting equipment for high-pressure chemical plants - disassembling, fitting, lapping, assembling.

3. Spool valves - grinding and lapping of sealing surfaces.

4. Rowing and sternwood shafts - gathering cones and fitting keyways in caliber.

5. Differential rollers of special design - sawing of supporting planes perpendicular to the axis with a tolerance of perpendicularity of 0.02 mm.

6. Propellers for shafts - fitting the hub on the cone of the shaft or in caliber.

7. Inserts - fitting and scrapping in the turbine housing.

8. Ducts of all types - control assembly and alignment.

9. Gyroscopes - preliminary and final assembly.

10. Internal combustion engines with power over 736 to 1472 kW (over 1000 to 2000 hp) - assembly, adjustment and commissioning.

11. Diffusers - fitting and fitting into the steam box and into the turbine housing.

12. Car retarders of all types - assembly, adjustment and maintenance in good condition.

13. Caliber propeller shafts and propellers with two or more key connections, with the installation of keys in any position relative to the grooves - scrapping and fitting the cone with keys.

14. Frames for radio devices made of profile steel with the number of incoming parts over 50 - assembly.

15. Frames and casing for turbines - manufacturing.

16. Carousels, leakages of vacuum installations - assembly.

17. Impulse valves and covers of all types and sizes - assembly.

18. Regulating valves, dual with a servomotor and with a dual system of levers - assembly, adjustment.

19. Valves of protective devices regulating - assembly, adjustment.

20. Valves, clinkets and gate valves with planetary gear drive - assembly, adjustment, delivery.

21. The main shunting valves of all types of ships - assembly, adjustment.

22. Steam valves with remote control - assembly.

23. Clinkets with a separate wedge with a conditional pass over 875 mm - assembly, delivery.

24. Kingstones and pneumatic and hydraulic actuated valves - assembly, adjustment, delivery.

25. Compressors and drying units (BO) with gas supply under pressure over 230 kgf / sq. cm up to 400 kgf / sq. cm - installation (connection of bench devices, valves, sensors, etc.), identification and elimination of defects that arose during the test.

26. Metal complex constructions: panels, rafts, plates, etc. for non-standard experimental technological equipment - manufacturing.

27. Digital and letter wheels - replacement.

28. Piston rings of a six-ton \u200b\u200bsteam crane - filing.

29. Piston rings with a diameter of over 400 mm - fitting the lock.

30. Piston rings with a diameter of over 550 mm - scrapping the ends and fitting to the piston.

31. Housings of vacuum valves and pumps, installations of chemical equipment - assembly.

32. The housings of the main and central devices, consisting of sections, are the assembly and connection of the sections together with the processing of places for mechanisms.

33. Instrument cases complex of various materials - assembly with the manufacture of individual elements.

34. Grinding wheels with a diameter over 750 mm - assembly, testing, balancing.

35. Covers - fitting to the turbine housing.

36. Lines of numbers in the numbering apparatus - adjustment and correction during assembly and repair.

37. The line of shaft lines of all types of vessels, except boats - pairing, installation on a machine (stand), deployment of holes, fitting of bolts, assembly, delivery.

38. Gravure printing machines - assembly.

39. Machines horizontal forging with pressure up to 20 MN - general assembly.

40. Agricultural self-propelled machinery - final assembly.

41. Mine hoisting machines with a bicylindrical drum - general assembly and adjustment with testing.

42. Auxiliary ship mechanisms - commissioning.

43. Lifting and anchoring mechanisms - assembly, testing and commissioning.

44. Mechanisms and fittings for remote control of ship and ship systems with electric, pneumatic and hydraulic servos - lapping, assembly and adjustment.

45. Thresher assembly - testing, running-in and surrender.

46. \u200b\u200bSteam hammers - assembly, inspection of steam distribution valves and valves, piston stroke, control mechanisms.

47. Couplings and half couplings of ship's shafts - cone scraping, groove cutting of keyways in caliber.

48. Elastic couplings of the main shaft line - assembly, balancing.

49. Guides with a triangular groove red-hot up to 340 mm long - grinding with a tolerance of +/- 0.01 - 0.02 for parallelism by 300 mm.

50. Gear pumps of various purposes and performance - assembly, testing, delivery.

51. Hollow shoulder blades packages - assembly and fit.

52. A rudder feather and a buller with a flange connection — scribing the flange planes, assembling the connection, aligning the center line, opening holes, fitting dowels, bolts and pins, delivery.

53. Feather of a rudder with a baller - scraping cones and keyways, fitting keys, assembly, delivery.

54. Planes, cams - processing according to 1 class of accuracy with certification of sizes.

55. Plane - scraping and adjustment of bores under the liners.

56. Pneumatic couplers like SPU-20, pneumatic wrenches like GPU-80 - assembly.

57. The surface of the compensator flange - scraping with an accuracy of at least 2 spots per square. cm.

58. Rolling bearings and combined - assembly.

59. Hydraulic presses with a force exceeding 30 to 100 MN - assembly, adjustment, testing, delivery.

60. Control panels and other complex automatic stations - complete manufacturing and assembly (without installation).

61. Diamond rollers of a difficult profile - balancing.

62. Rotors - static and dynamic balancing.

63. Rotors, turbines - assembly, installation of a thrust bearing.

64. Rotors - assembly of shovels with retaining fastening.

65. Servomotors - assembly lock.

66. Beds of longitudinal milling and other machines - installation on shoes with alignment on the water level and string with an optical device.

67. Beds of unique and precision machines - scraping guides.

68. Precision turning machines - carriage and caliper scraping.

69. Screw-cutting lathes - testing the machine for power with adjustment and adjustment, accuracy test with adjustment, adjustment and correction of defects.

70. Experimental turbochargers, air and oxygen compressors - final assembly, adjustment and delivery.

71. Knots, mechanisms, designs of large vessels - installation using plastics.

72. Units of pneumatic jacks of shock action - assembly, adjustment.

73. Complex units, assemblies and machines of experimental designs - assembly and testing.

74. Units complex and units of cars of the highest class - assembly, adjustment, testing.

75. Gas turbine units - assembly.

76. Steering devices - assembly, adjustment, delivery.

77. Perforating device - final processing of incoming parts after hardening, centering punches on dies, observing dimensions within tolerances of up to 0.01 mm.

78. Centrifuges - grinding of a shaft with a rotor and sealing rings, assembly, adjustment and testing.

79. Cranks and regulators of the crane, cases of water feed pumps, jacks - assembly.

80. Gears assembly - static and dynamic balancing.

81. Electric spiers, drive spiers mechanisms - assembly.

82. The probe after hardening - pressing into the guide with a tolerance for parallelism +/- 0.01 per 120 mm of length.

83. Eccentrics - final machining after quenching with the removal of tables on the comparator.

84. Electric guns of blast furnaces - disassembly, assembly.

§ 91. Mechanic assembling works of the 6th category

Description of work. Assembly, adjustment, testing and delivery in accordance with the technical conditions of complex and experimental, unique machines, machine tools, units and apparatuses. Checking the correctness of their assembly with the removal of operational diagrams and characteristics. Installation of high pressure pipelines for any applicable gases and liquids. Elimination of detected defects. Calculation of gears, eccentrics and other curves and their verification. The construction of geometric shapes. Participation in the design of a passport for assembled and tested cars.

Must know:   design, principle of operation of complex machines, machine tools, units and apparatuses; methods of static and dynamic testing; methods for debugging and adjusting manufactured machines, devices and other equipment, the principle of calculation and methods for checking eccentrics and other curves and gears; methods for calculating and constructing complex figures; rules for filling out passports for manufactured machines.

Work examples

1. Devices of mechanical centralization, mechanisms of auto-barriers, axial reducers of track layers - assembly and adjustment.

2. Unique numbering devices (for special orders) - assembly and adjustment.

3. Cylinder blocks of internal combustion engines - installation of piston, spool and camshafts with alignment of axial lines.

4. Shafts of cranked machines and internal combustion engines - installation, alignment and inspection with adjustment.

5. Crankshafts of steam engines of various types for large vessels - fitting keyways, calibration of crank necks with an accuracy of 0.03 mm.

6. Shafts transmission roller tables - assembly.

7. Gas turbine units - adjustment.

8. Internal combustion engines with a capacity of over 147 kW (2000 hp) - assembly, adjustment, commissioning.

9. Gate valves with an integral double wedge of the II and III degree of pressure - assembly, adjustment, testing, delivery.

10. Remote control bellows valves with cup springs - assembly, adjustment, testing, delivery.

11. Non-circular gear wheels - metalwork, assembly with a hub, final processing after hardening, installation.

12. Columns with parallels of steam engines and internal combustion engines - installation, alignment, alignment and adjustment.

13. Compressor automatic stations with gas supply under pressure of 400 kgf / sq. cm - installation on a test bench, installation (adjustment of fuel, oil equipment, start-up systems, valves, sensors, etc.), identification of defects in the system and their elimination, calculation of all characteristics, delivery to the customer.

14. Octagonal compressors - manufacturing and assembly.

15. Conoids - installation on the device, the final processing with the removal of the allowance according to the tables on the comparator.

16. Brackets for steering servo motor - assembly.

17. Automatic lines consisting of modular machine tools - assembly, commissioning, testing, delivery.

18. Shaft lines of large vessels with weldable shafts in diameter over 600 mm - installation on a stand, alignment, expansion of holes, fitting of bolts, assembly, delivery.

19. Working blades, guides, nozzle and diaphragms - fitting for density at the attachment points with preservation of passages according to technical conditions or drawings.

20. Machines horizontally forged with a force of over 20 MN - general assembly.

21. Steam engines - final assembly, testing and delivery.

22. Hydraulic steering machines and variable displacement pumps - assembly, installation, testing, commissioning.

23. The main ship mechanisms - commissioning.

24. Disconnecting couplings - calculation and adjustment of mating parts.

25. Couplings connecting turbines (TVD, TSD, TND) - fitting fit.

26. Turbine clips, steam shields, diaphragms - fitting to the turbine housing.

27. Electrovacuum equipment (installations) with program control - assembly, adjustment, testing.

28. Samples of the head experimental and experimental ship valves: automatic, bellows, safety - experimental assembly, testing in the presence of the commission, bringing the design to its final form.

29. The sealing surfaces of the hulls and covers of ship fittings with bezkladnochnoy connection with a diameter of more than 200 mm - grinding and lapping of the sealing planes.

30. Thrust ship bearings with combined tarsion system - final assembly, testing, delivery.

31. Hydraulic presses with a force exceeding 100 MN - assembly.

32. The devices are complex, with differential clutches, with the calculation of gears - assembly, mechanical and electrical adjustment, testing and delivery.

33. Planetary and globoid gearboxes over two stages - assembly.

34. Machine tools, precision metalworking - assembly, final verification of accuracy, testing and delivery.

35. Unique metal-working machines with a hydrocopy device - assembly, adjustment, testing and commissioning.

36. Counters of temperature regulators, tables of welding plants, heads of welding plants, vacuum sensors, tables of coordiographs, units for plants for the production of solid circuits - assembly and commissioning.

37. Traverses of the main lift of filling and pouring cranes of open-hearth shops - assembly.

38. Pipe-air ducts tangent, elliptical pipes, tangent inlets - control and enlarged assembly.

39. Steam turbines - checking the gap between the blades, the casing and the rotor; diaphragm seals, stuffing box seals in thrust and thrust bearings.

40. Steam turbines - landing of disks on a shaft, installation and balancing of rotors (static, dynamic), final assembly, testing, delivery.

41. Turbines with gearbox and main thrust bearing - checking alignment when installed on a stand and a vessel.

§ 91a. 7th category mechanic assembly work

(introduced by Order of the Ministry of Health and Social Development of the Russian Federation of November 13, 2008 N 645)

Description of work. Assembly, regulation, testing and delivery in accordance with the technical conditions of unique designs, valves, gas distribution systems, pumps, chambers, apparatuses, boxes. Assembly and regulation of complex experimental units and machines. Identification and elimination of defects, making proposals for changing the design documentation based on the results of assembly and testing of complex experimental units and machines. Registration of test results and delivery of products using electronic computers. Participation in the development of conductors and mandrels for the precise manufacture and assembly of complex experimental products. Carrying out accurate measurements of complex parts using special coordinate machines, measuring heads, laser scanners, copy machines, computer equipment. Ensuring the required cleanliness of processing of internal and external surfaces and welded joints. Polishing surfaces. Calculations and manufacturing of complex reamers of apparatus from heat-resistant, experimental steels and alloys.

Must know:   rules for the execution of sketches of parts and assembly units; rules for the use of computer technology; ways to ensure accuracy in measuring complex parts and surface cleanliness; methods and techniques for assembling, ensuring the stability of products under climatic, mechanical and radiation influences.

Secondary vocational education is required.

Work examples

1. Cameras, devices, boxes for chemical production in the processing of radioactive materials - manufacturing and testing.

2. Containers for storage and transportation of radioactive materials and products - manufacturing and testing.

3. Vessels operating under pressure, containers with technological solutions of radioactive materials - manufacturing and testing.

4. Stamps and molds - assembly, regulation and testing.

Mechanical assembly fitter is a difficult profession, and not everyone is able to master it. The reason is that future specialists will have to study the structure of many mechanisms, and this requires an innate talent for memorization. In addition, the mechanic for assembly works must have the ability to cancel endurance and strength, because the specifics of the work will repeatedly force you to encounter heavy parts and mechanisms.

And yet, one who has mastered this specialty can be sure that he will have a decent job. After all, locksmiths are always needed in enterprises, especially highly specialized ones.

Who is a fitter?

This branch of specialists is engaged in the assembly of mechanisms and devices. In particular, it is they who install various kinds of turbines, motors, nozzles, heating units and so on. If we compare an ordinary locksmith with his mechanical assembly colleague, the second is different in that it has more in-depth knowledge in the field of mechanics.

If at ordinary enterprises there is no special need for such specialists, since an ordinary locksmith can fulfill their obligations, then at factories for the production of various equipment they are simply irreplaceable. Especially where they create high-tech mechanisms and assemblies that require increased attention in manufacturing.

How to become a mechanic for mechanical assembly work?

You can get a locksmith qualification at a technical school or college. Upon admission, you will need to pass an exam in physics and mathematics. You cannot call them simple, so you should prepare in advance, and if necessary, hire a tutor.

Another way is to get an apprentice to an experienced specialist. After several years of such training, you will turn out to be a real mechanic of mechanical assembly work. The responsibilities of the apprentice exclude operations of increased complexity, so you should not count on full payment. But still, given that this is only a stepping stone to the desired profession, such a distribution of the budget can be tolerated.

Search for a suitable job

Finding a job as a mechanic will not be difficult, because they are necessary at any enterprise. Remuneration will depend on the size of the organization and the responsibilities that will lie on the shoulders of a locksmith.

As for the search for vacancies in the specialty "mechanic assembly works", then everything is more complicated. Indeed, in small enterprises there is no need to categorize locksmiths, and no one will pay extra for highly specialized education.

Therefore, it would be wiser to look for work in large enterprises. Here, modernization of machinery and equipment is constantly being carried out, which means that the services of a fitter will be relevant. Also, do not forget about the factories that manufacture machine tools, various kinds of tools, units and so on.

If there is nothing suitable, then you can get a job with related specialization. For example, a mechanic for monitoring automation or a toolmaker.

What is the responsibility of a mechanic assembling?

A lot in the future profession depends on the particular production chosen. After all, it is one thing when a person works at a car factory, and the metal rolling industry is quite another. Nevertheless, it is possible to bring certain parallels.

Locksmith duties have the following:

1. First of all, a locksmith must be able to work with various mechanisms: assemble them on the basis of drawings, customize parts, configure and check for suitability.
2. Also, the duties of a locksmith include repair. Firstly, he is responsible for the serviceability of his manufactured products. Secondly, he is obliged to repair all the mechanisms on his site in order to prevent production downtime.
3. Regardless of the type of production, he must obey superior management.

Job description locksmith mechanical assembly work

Upon entering work, each locksmith must sign a series of documents. Among them there is an instruction of a mechanic assembling works. It just indicates all the duties and rights of this worker.

The job description of a mechanic for assembly works is a set of rules, and it is strictly forbidden to violate them. In general, such a document can be divided into four large sections.

1. The main provisions. Here are the requirements for the employee in need: a list of necessary documents, his position in the workplace, at whose disposal he will be located, and so on.
2. Tasks and responsibilities. A list of all operations that a specialist will have to perform in the specified production.
3. Rights. A list of what a locksmith should do: the length of the working day, the presence of lunch, and the like.
4. A responsibility. This paragraph outlines all situations that could entail financial punishment.

Mechanical Assembly Worker: Discharges

There are 5 tariff categories. The youngest is the second, the eldest is the sixth. For admission to work of increased complexity, you must have a rank of at least 5th.

Naturally, the higher the rank, the greater the chances of finding a well-paid job. Nevertheless, the mechanic of assembly works is a profession where experience is most valued, not a diploma. Therefore, it is likely that the first 2-3 years will have to work in a small enterprise and only then apply for more promising vacancies.